Professional On-Counter Frothing Pitcher Rinser w/5' Hose & Drain Valve
This is a very useful, yet simple appliance that allows a busy barista to keep their frothing pitchers clean. And not only does it clean out frothing pitchers, but it cools them off in a hurry - the way you want them for optimal frothing.
This rinser will clean any glass, pitcher, cup, shot glass, or coctail shaker by simply pushing it down on the center of the nozzle in its sink. If you look at the closeup photos, you'll see that the nozzle in the center of the appliance has little jets on top of it. When you push your pitcher face down on the hexagonal rods, the jets in the center of the star will blast the inside of your pitcher clean.
This countertop rinser stands on the counter, and connects to your COLD water, and to your drain with external hoses that need to be routed from beneath the countertop. While this unit sits ON the countertop, it has a water input line and a drain line that must go THROUGH the coutertop. These are two 3/4" holes that are about 3" apart (wait to get your unit before drilling!).
So the only work you'll need to do is to drill TWO holes in your countertop, and hook your sink up. The unit COMES WITH a 5' hose that screws onto the water input of the unit. You'll need to connect the other end of that to a cold water source, and provide your own drain hose (which could simply be a bucket under the counter). The unit also comes with a 3.5" long hollow (3/8" inner diameter) drain bolt with a nut to connect the drain line through your counter and bolt it in place.
The press fittings in the water input valve are not meant to handle hot water. The good news here is that as it cleans your pitcher out, it also cools it down. To make high quality froth, it’s best to start with COLD milk in a COLD pitcher.
Note that because this uses cold water, and it doesn't use soap, this doesn't provide sterile cleaning - it is NOT meant as a cleaning appliance for glasses and cups that people drink out of. But it does provide a serious blast of water to rinse out things as you use them. Without this, you would likely not clean things like frothing pitchers between drinks anyway. This sink allows you to improve on that - and to improve on your froth, since it makes the pitcher cold.
This countertop washer stands a mere 7/8" above the counter, and is 7" wide by 24" long. Any vessel up to 4.5" in diameter can be pushed down into the sprayer to be rinsed out, but this is meant primarily for frothing pitchers. Note that because this is 24” long, there is lots of drain area to leave 2-3 additional pitchers to drain after you’ve cleaned them out.
The hexagonal-star frame (onto which you push your face-down pitchers) operates the ON valve for the water spray. All you need to do is to push the frothing pitcher down onto this frame. This turns the water on. Remove it, and the water shuts off. This is a very handy and simple rinser. It's even good to use on clean pitchers, because it makes them cold - which is what you want for a high-quality froth. And in the case of this 24” X 7” appliance, there is plenty of room there to leave 2-3 rinsed-out pitchers to drain.
The cold water input valve is a 3/8" Press Fitting connection. It will give you a water-tight seal just by clicking it into place. This does not require tools - you can do it by hand. The drain line is a standard 1/2" barb fitting - you'll simply push a rubber hose onto the nozzle, and run the hose into your sink.
- Appliance is 24" X 7", and stands just 7/8" above the counter;
- Will fit any glass, cup, or pitcher up to 4.5" in diameter;
- It "installs" merely by running a cold water line and a drain line to it;
- Hexagonal assembly has ridges along its arms to prevent your pitcher from moving;
- The drainage container is stainless steel;
- Cold water connector is a 3/8" press fitting (doesn't require tools to install);
- USE COLD WATER ONLY; hot water will damage the press fitting;
- Drain connector is a 1/2" barb fitting - simply push the drain hose onto it.